AptifoldContact
← Return to the point-follower foundry

MOVEMENT FOUNDRY / A DIFFERENT CONTACT

Use a roller.
Keep the movement.

Imagine a small gate that rises, waits for a part to pass, then lowers. A motor keeps turning; a shaped wheel sets the gate’s movement.

Put a roller on a wheel made for a pointed tip and the timing can change. Keep the same job and wheel size here, then reshape the edge for the roller.

The interactive workshop has not started. If it stays here, reload this page. The original point-follower tool and model notes remain available.

ONE JOB / TWO EDGES

The edge has to change.

Checking geometry

Requested lift…
Roller lift…
Difference…

The roller’s centre follows the guide. Its edge touches the side of the shaped wheel.

Select a position around the wheel or on the trace below. Arrow keys inspect the turn. Playback is optional and shows no operating speed.

SAME TOP HEIGHT CAN HIDE DIFFERENT TIMING

When does the gate actually move?

Requested Reused point shape New roller shape

The curves come from wheel/roller contact, not a drawn animation. Select a turn position. The new curve follows the requested line when this construction passes.

TRY A CHANGED CASE

A bigger roller has to fit the bend.

These are illustrative jobs. A failed chosen-size construction is separate from ruling out every possible cam.

CHANGE THE JOB

Tell the gate what to do.

One turn contains a rise, a pause at the top, a return and any remaining pause at the bottom. More angle for a movement spreads it over more of that turn.

The contact tilt is the angle between the contact normal and the upright guide. It is a geometric limit you choose, not a force calculation or an industry recommendation. The shaft allowance is a chosen radius, not a strength check.

INSPECT THE CHECK

Contact, clearance and the whole curve.

Separate requirements for this selected construction
RequirementCurrent resultWhat it establishes
Exact geometry, interval coverage and sources

The roller centre is not the wheel’s edge

Let E be the selected outer wheel radius, h the lift and a the roller radius. The cam base is b = E − h; this bench uses all the stated room. With the native quintic displacement s(θ), the roller-centre path has radius R = b + a + s. In body coordinates C = (R sin θ, R cos θ). The working edge is C − aN, where N is the outward unit normal of that path. Rotation by positive θ puts C on the fixed upright guide.

The rise and return use 10u³ − 15u⁴ + 6u⁵. Their first and second derivatives match the pauses. Third derivatives need not match. Shape does not establish maintained contact under a real load; contact is assumed here.

The supported continuous check

For a finite roller, this workshop supports a strictly convex roller-centre path. It checks Q = R² + 2s′² − Rs″ > 0 and (R²+s′²)³ − a²Q² > 0 over both complete motion segments, with derivatives in radians. The second inequality means the local radius of curvature exceeds the roller radius. Pauses satisfy the conditions analytically when b > 0.

Outward-rounded intervals enclose those polynomials on adaptive dyadic pieces. A positive lower bound across every piece qualifies the declared condition. A midpoint interval can prove a failing witness. A depth/node limit is unresolved and never becomes a pass. A nonconvex path is outside this check, not proof that every roller cam is impossible. At a = 0 the established point construction applies.

For a qualified convex path, its inward parallel stays within E and outside the b circle. Clearance requires b to exceed the chosen minimum radius. The existing continuous pressure bound applies to the centre-path base b+a. Comparisons within a 1e−9 relative length band are on-limit rather than a robust pass. No minimum-size optimization, force, wear, manufacturing tolerance or physical safety qualification is claimed.

Replaying the actual outlines

The comparison rotates 1,440-segment polygons and expands each vertex and edge by the roller disk, then intersects the upper envelope with the guide. It does not use the requested displacement or analytic normal to reconstruct contact. The plotted comparison samples every 2°. Polygon approximation and rounding remain separate from the continuous check.

Accepted interval pieces. Each motion segment covers u = 0 through 1 without gaps when the check passes.
Segmentu fromu toQ lower boundOffset-polynomial lower bound

Sources

CMU: cams, trace points and roller envelopes · Ablamowicz and Liu: inward offsets, curvature and cusps, section 5. The new restricted-family formulas are derived for this workshop. Those references do not validate the implementation or a physical mechanism.

Keep a design you can inspect.

Save the inputs to reopen this job, or export the checked conceptual outline in millimetres. The SVG always contains the new edge, including while you inspect the reused shape. A design record includes the calculation, interval pieces and sampled replay. Reopening a setup recalculates it.

APTIFOLD / AGENTIC AI

What would you like to work through?

Aptifold develops its own agentic AI to investigate questions, test ideas and build working software. This experience is one example of that work.

Explore Aptifold Discuss a question

Company links open in a new tab, so you can keep this experiment open.